New Arrive Dog Training Collar 8806-2 Model Rechargeable and full waterproof Collar With 2 Collar nf
Note:  This link include one remote and 2 receiver collars
IMPORTANT NOTICE
1. In order to save power, the display will turn off after 10 seconds of no operat'ion, and the remote will fall into sleep mode after 30 seconds of no 'interaction You can reactivate it by pressing any button
2. lf there is no operation within 5 minutes, the receiver will fall into standby mode, you can press the  'Y" button to active it
3. If the training collar set is NOT sensitive, please review the following questions
1) Are the remote and tHe receiver too far apart?
2) Are there any barriers/interferences between the re m ote and the receiver?
3) Are the remote and the receiver fully charged?
4) Are the remote or the receivers in standby mode?
5) Are the two modes swiiched frequently?
6) Is the button pressed too lightly or are you pressing the center of the button?
4. The IP67 waterproof feature protects the receiver and remote from getting wet. However, they cannot
be submerged in the water for a long period of time.
5. Misusing the dog training collar may injure your pet. Please read the instructions carefully
before using it.
Tips
1.DO NOT use on puppies younger than 6 months. It is recommended to use on medium/large dogs.
2Training collars should be used to help fix behavioral issues, not for punishing/abusing animal.
3. Recommend to use vibration/tone mode to train your dog. Improper use of the shock mode may cause
pain/physical 'injury or may traumatize the dog. So the shock mode should only be used in case of an  emergency, and should not be used as a form of positive behavior training.
Key Definition
Antenna: It wll~ash when transmits signal and charging
'Y'Button: Press the button to send signal.
3 Touch Button: Adjust the vibration l shock level from 01 t0 1 6, clockwise is adding, counter-clockwise
is reduing.
Channel Button: Press this button to select a training channel (A/B/A? B).
Note: lf you have one receiver, you can select one of the three channel to use. If you have two receivers
please pair them to different channel, you can controlthem separately, we recommend top air channel A
and channel B, so you can select channel A+B to control them together. Note: The channel A and
channel B is an independent channel, channel A+B is the common channel.
lf you pair channel A, channel A and channel A+B both can work. Pair channel B is the same If you
only pair one rece'iver to channel A+B, three channels all can work.
Mode Button: Press the button to select the Shock/Vibration/Tone mode.
LCD Screen: Shows the modes, levels, battery and channels.
Rubber Caps: Place on top ofthe touch points to prevent skin damage.
Indicator Light: The light will flash when you press the shock/vibration/tone button, when the
receiver is charging, the light will flash.
Power Button: Press to turn the receiver on and off.
Remote Charging Seat: Charge the remote
Receiver Charging Seat: Charge the receiver
Chargerlnput Port: Micro USB port, please input DC 5V.
FAQ
Q: How long is the remote range?
A: The remote range is 875 yards if there are no obstacles interfering. The remote range may be reduced   due to some interferences and obstacles.
Q: What is the length of the belt collar?
A: The dog collar fits neck sizes from 7.1 t0 25.6 inch
Q: What is the recommended weight for dogs to use?
A: We suggest above 20 lbs.
Q: Is the receiver waterproof?
A: The collar receiver is lP67 waterproof. Allowed to be used on rainy days. (Cannot be submerged in
water for a long time)
Q: What should I do if the training colla r set doesn't work?
A: 1 .Check if the receiver and the transmitter is fully charged.
.2 .Make sure all the adjustable modes are set above level l.
3.Check the Receiver. Press the Power button to turn on the Receiver.
4.Check the channel. Make sure that you are on the same channel with the collarthat you paired up with
5.Checkthe metal screw cap if they are too short. Change to install a longer cap.
6.Rematch the Remote and the Receiver.
How to Train a Dog?
Notice before training
1 . Avoid "Collar-Wise'
It is important that your dog is aware that the correction is coming from the colla r. He will not    misbehave when he wears the collar, but does as he please when collar is off. This is what we called     "coHar-wise".
Tips:
Before training, let your dog wearthe electric collar for about 5-7 days (no more than 8 hours per day)   so that he can be accustomed to the weight of the collar and believe it is just another normal collar.
2. Timing is crucial
The more precise the timing ism the quicker your dog will make the association and change his or her    behavior.
3.  Praise your dog
It will be helpful to praise your dog as soon as it responds to the colla r. Reward it with a pat, by saying    'good dog", or with a specialtreat.
4.  Don't let your dog know the secret
Don't let your dog know that it is you causing the unpleasant sensation around its neck    your dog associate the sensation with bad ehavior.
5. Know intensity of each mode
Knowing the intensity of each mode will be helpful to control the stimulations.
SHOCK: Level l of shock mode is like getting bit by a small insect or Chinese Acupuncture
it yourself, however, please be very cautious if you want to test a higher level.
VIBRATE: Level l of vibration mode is like the vibraiion of incoming call of an iPhone. It is recommended
to use vibration mode first. and use the shock mode last.
Setting the initial training leve
To set the initial training level, you must first determine the lowest stimulation that will clea rly get your
dog's attention by the following steps:
1 . Set stimulation at zero.
2. Fit the collar properly on your dog's neck and start the training.
3 . If he doesn't focus on you, begin the stimulation and progressively increase the levels until he responds
to the shock/beep/vibration.
Tips:
1 . At the point that your dog responds with head tilt or ears prick up, or other signals, show signs of    responsiveness. This is the level at which you can begin yourtraining.
2. If your dog yelps orjumps, shows signs that the level is too high.
3. Every dog is an individual and unique. Some are more sensitive than others, and some learn more    slowly or quickly. So be sure to test out each level on each individual dog.
Stopping Unwanted Behaviors
For this type of training. you need to set the collar at the predetermined stimulation level discussed above
Steps:
1 . Let your dog roam in the area where he might misbehave, for example eating garbage.
2. Get yourself out of his sight or at a discreet distance, and wait.
3. At the instant your dog misbehaves, you press the button. This will send a signal to your dog's neck     so that he will associate the signal with his misbehavio r. lf he doesn't respond, you should increase    the level.
Tips
Timing is crucial. Catching the unwanted behavior and sending the signal at the precise moment can
drastically shorten training time.
Reinforcing Learning Behaviors
If your dog knows the command but responds inconsistently, or acts slower than your requirement   an e-collar can sharpen his skill.
For example, you have taught your dog to come when called, but over time he responds slower. You
can communicate with him via the remote trainer, so that he immediately responds to your call.
Steps
1. Set the electric collar to initial stimulation level and test it
2. Fit the collar on your dog's neck along with his regular collar.
3. Let him roam around the training area. Then command him"5it Down"or "(ome Here' or whatever     would he knows and simultaneously press the stimulation button.
4: The insta nt your dog moves toward you, stop stimulating and then praise him.
Tips:
1 . If he doesn't get it for the first few times, don't give up and do not increase the stimulation. Try to    work on this a couple of times per day.
2. During the training period, never give the command if you are not able to enforce it. Your dog has to    make the mental connection between the shock/vibration/beep to his behavior (may to ke a week or    more for some dogs).
Altogether, both methods of stopping unwanted behavior and reinforcing learning behaviors can be    applied to nearly every training scenario.
Training collars are used to train the dogs instead of punishing. Please use properly with care. Electric    collars can be a safe and effective tool to train, build communication, and strengthen your bond with    your best friend.
May this manual be helpful for you. For more dog training methods, please search on Google. For more    pet supplies, we also sell pet seat covers, dog leashes, pet ca rriers, and more.
Frequency: 915MHZ
Transmitter: 3.7V 300MA LIP
Receiver: 3.7V 500MA LIP                Madein china